Archive | Renovate It RSS feed for this section

Kitchen Cabinet Restaining…

12 May

I’m about all Java-gel stained out. Well, to be honest I finished back in October 2014, but I STARTED in May 2014. Took a bit of a hiatus while I settled into a new job over the summer, and feverishly worked in the fall in order to complete them by Eloise’s first birthday party. Task accomplished! But it wasn’t without some major burnout in the end.

This recap isn’t a how-to (you can find that here); it’s a before/after plethora of photos so you all can get a feel for what this technique can do for the look of your kitchen (since my bathroom redo is a much smaller space).

Here are a few before photos:

DSC_0085

DSC_0087

Notice the upper cabinets in the photo below – can you see how uneven the knobs are? Due to settling in our house (it’s over a half-century old), everything was a little crooked. I’ll address this issue toward the end of the post.

DSC_0088

I just wasn’t into the honey-oak color, and honestly they were looking a little worse for wear over the past 60 years or so. I love white cabinets, but I didn’t want to paint them because I was afraid of chipping where the doors hit the cabinets, plus these are just so flat and smooth – not much margin of error for paint. Plus, I just like dark, especially with our light floors.

So, here are few “during” photos.

Getting started – there’s still life left in me. Dare I say it – I’m energetic about this project! The ol’ sock hand is back and rarin’ to go!

DSC_0096

Just a reminder of the streaky ugliness of the first coat – this is normal.

DSC_0098

Not a pretty picture of our kitchen while I did the lower cabinets.

DSC_0099

DSC_0100

This is me, in between complaints to my husband about how sick of this project I was.

DSC_0506

But this story has a happy ending! As much as I complained about it, it was WORTH IT!

DSC_0045

DSC_0046

DSC_0043

I used the same oil-rubbed bronze knobs from before. I wasn’t sure at first how the dark knobs would look against the dark stain, but I really think it turned out well.

DSC_0047

We replaced all the hinges from the previous original copper-colored ones to these oil-rubbed bronze ones. They really blend in nicely since these old cabinets don’t use hidden hinges like most new cabinets.

DSC_0049

I would be remiss if I did not mention the work that my husband, Ryan, put into these cabinets as well. If you recall that “before” photo from above – the uneven knobs – that issue would come to bite us in the behind at the end. We basically realized we’d have to refill the holes on the doors and the cabinets and rehang pretty much every single one of the 33 doors. Let’s just say I didn’t do it, so thank you Ryan, for rehanging the cabinet doors and for putting up with all my whining. Both were very challenging and annoying.

So, now that I’ve been officially done for 7 months, here are a few pros and cons for those of you thinking of doing this:

Pros:

  • Beautiful! (If you like dark, rich cabinets. They’re not black – they’re dark brown.)
  • An easy, simple and pretty much foolproof process (here’s that link again)
  • Pretty durable so far. It’s gotten a couple knicks, but nothing I can’t touch up with a tiny paintbrush. And some of those knicks might have been due to the rehanging process.

Cons/tips:

  • Time-consuming when you’re working with a large area like this. I had a system down where I completed three coats of stain on one side, then turned them over to complete the other side. Be sure to put a towel down so the first side doesn’t get scratched while you’re doing the second side. Then repeat when you do the poly.
  • They’re a little shinier than I prefer (however, some of the photos look WAY shinier than they do in person). I used the General Finishes satin finish, and as far as I know they don’t offer any poly finishes that are less shiny than that. I wanted to use the General Finishes brand poly to match the gel stain (the guy I bought it from couldn’t guarantee how another poly would work with it), but I prefer a less-shiny finish. Maybe if I was doing a table or something small, I would try a different, more matte poly.
  • Fingerprints are more noticeable due to the finish and the dark color. I knew this going in and did it anyway because I didn’t care. I just wipe them around the knobs with a dishrag every now and again – it’s not that big of a deal. And it actually grosses me out to think about how dirty my cabinets were before I did this! 🙂

So, if you have any questions, please do not hesitate to ask. Best of luck!

KitchenStainBeforeAfter

Working with Epoxy Resin

12 Aug

This resin desk is one of the coolest, yet most challenging project I’ve done so far.

A friend of mine had a stack of coasters that she and her husband had collected from a trip to Europe. They were just tucked away in a Ziploc bag, and after she saw my post about the Starbucks table, she was wondering if I could do something similar for her with the coasters. She was hoping to make them into a desk for her husband as a surprise for his birthday. I figured, how hard could it be? 🙂 Famous last words…

Here’s the desk that we started with (sorry; I didn’t assemble it after she brought me the desk, but you’ll see that it’s white, and it would end up black).

IMG_1116

This is the resin I used. I bought it at Lowe’s for about $24 a box.

DSC_0671

First, I primed all of the desk pieces with a black spray primer. After doing some testing with the resin on some other pieces, I decided that it was necessary to create a sort of “fence” to hold in the resin. After all, resin is first poured on in liquid form and cures to be hard, so somehow I needed to hold in the resin in. Tape didn’t work on my test pieces – the resin leaked out of the tape. So a fence it was. However, this fence had to stay put – I wasn’t going to remove it after the resin was cured. So it had to look like part of the desk.

I found some simple 3/4″ trim that had rounded edges on the top, and I had Ryan cut it to size for me. I glued it to the desk, then used the air nailer to make sure it was secure.

IMG_1117

I had some pretty sharp corners, so I hand-sanded those down to blend into the rounded corners of the desk.

IMG_1121

Next I filled the inside and outside seams with some paintable caulk. Even though the fence holds the resin in, it still needs to be “water-tight,” otherwise the resin would leak out (like it did with the tape).

The last thing I did before putting the desk back together and starting on the resin portion was painting the whole thing black. I used spray paint again, as there are lots of nooks and crannies on this desk, and spray paint ensured an even coat.

Okay – on to the fun part! We set up and arranged the coasters, and I glued them on using simple Elmer’s Glue All.

DSC_0462

After some intense leveling, we mixed up the first coat of epoxy resin and poured it on (there are two bottles that you mix together on a 1-to-1 ratio). There is one main thing to remember when working with resin – mix and mix some more! If you read the directions and follow them carefully, you’ll be fine. I overlooked one step, and that would come to bite me in the butt down the road – in a big way.

DSC_0468

Then pour… DSC_0470

We then used a combination of stick pins, a hair dryer and blowing on it with our own breath to bring the bubbles to the top. We had to deal with bubbles for quite awhile (I think we had an hour or so of working time before it started to cure up) because the coasters still had a bit of air under them when I glued them down.

One coat of resin didn’t quite cover the coasters, so after 3 days of cure time, we added another coat…and this is where I went wrong. I ended up scraping some of the last bits of resin out of the cup, and it hadn’t gotten completely mixed together. It all looked great until we came home after being gone for the weekend. There were a few sticky spots about 3″ in diameter. After some major panic, I contacted the company on the box and they assured me that I could sand down those sticky spots and flood the desk again. So, Ryan and I actually dug out the worst sticky spot with a razor blade and sanded that down along with the other spots, and boy did it look terrible! 🙂 It was very cloudy and I hoped and prayed that the 3rd coat of resin would clear it up as the company told me.

Turns out, they were right! The third and final coat cleared those sanded spots up like magic. It turned out beautifully, but it was a long road to get there! Both my friend and her husband like the desk, and that’s all that counts. 🙂

DSC_0561

DSC_0566